vessel flange
英 [ˈvesl flændʒ]
美 [ˈvesl flændʒ]
网络 容器法兰
双语例句
- In this article, the treatment for the leakage occurred in the vessel flange of the heat exchanging equipment due to the variation of the pressure and temperature was introduced.
本文简要介绍了换热设备大法兰在温度及压力变化情况下发生泄漏后的不同补救措施，对于不停车等情况下的消除设备隐患的良好效果。 - Nozzle projections are from the vessel centerline to the gasket face of flange.
喷嘴设计是从容器中心线到法兰密封面。 - The application of this software has shown that it is simple and easy to apply. The intelligent pressure vessel and pipeline flange clamp design was achieved preliminarily.
应用实例证明了该软件的实用性和易用性，初步实现了压力容器和管道法兰夹具设计的智能化。 - The Points Which Should be Taken into Account when Utilizing the Standard of JB4700~ 4707-92 《 Pressure Vessel Flange 》 in Chemical Equipment Design
在化工设备设计中选用JB4700～4707-92《压力容器法兰》标准应注意的问题 - The Leakage and Prevention of PWR Pressure Vessel Flange
水堆压力容器法兰的泄漏与防止 - Dynamic Disposal Skill of the Local Leaking on the Vessel Flange
容器法兰局部泄漏的动态处理方法 - The Stress Analysis of Vessel Flange with Definite Element
容器法兰应力分析 - One of the basic failures of reactor pressure vessel is the failure of flange sealing system, so it is very important to study the performance of its sealing system.
法兰密封失效是核压力容器的最基本失效形式之一，研究其密封性能具有十分重要的意义。 - The common methods and points taken into account of the standard of JB4700~ JB4707-92 《 Pressure Vessel Flange 》 were introduced.
介绍了JB4700～4707-92《压力容器法兰》标准在设计选用中的一般常规方法和应注意的问题。 - TheC-type sealing ring is designed to pressure vessel flange seal.
C形环是一种用于压力容器法兰密封的密封环，目前国内使用的为进口C形环。 - Several Proposals on Pressure Vessel Flange Standard
关于压力容器法兰标准若干问题的建议 - Aimed at the final shaping process of flange sealing-face of several pressure vessel, a mechanically processing device fixed onto the flange hole of processed flange end surface for sealing groove processing was introduced.
针对一些压力容器法兰密封面的最终成形工艺，介绍了一种装卡在被加工法兰孔中加工法兰端面密封槽的机械加工装置。 - The hoisting of thick wall heavy-duty vessel is suitable to install hang cover and big flange specially.
高压厚壁重型容器的吊装，宜直接设置专门吊益与大法兰用螺栓把紧起吊； - Pressure vessel shell manufacture process, flange welding edge with the shell wall thickness increasing processing brought about by a serious processing problem.
压力容器筒体在制造过程中，遇到法兰焊接坡口随着筒体壁厚的不断增加，带来了严重的加工问题。 - Head is mainly confined part of pressure vessel. Not only the size is increasingly large, but also the shape is complex day and day. The large head with flange which used in hydrogenation reaction is a typical case.
封头是压力容器的主要承压部件，不仅其尺寸超大，而且形状也越来越复杂，加氢反应器用大型带法兰封头就是其中典型一例。